Company: ASHOK LEYLAND
art 1: Engineering Aptitude (50 Questions – 25 Minutes)
Physics
Maths
Mechanical Engineering
Electrical Basics
Part 2: Mechanical Comprehension (50 Questions – 30 Minutes)
Basic Production Engineering
Mechanical Figurative Questions
Part 3: General Aptitude (60 Questions, 30 Minutes)
Analogy
Analytical Reasoning
Verbal
Quantitative Aptitude
Figurative Puzzles
Alphabetical Puzzles
Part-1: BASED ON 11& 12 FUNDA.
Electrical circuit
Effect of addition of salt on water (related to solutions)Over turning of vehicle in circular track (conditions of skidding, etc)
Effect of pressure on boiling
Buoyancy effect
Effect of rubbing glass with silk & rubber with_________ (nature of charge produced)
Forces on charges
Time period of pendulum
Body temperature in f, temperature common on both c &f scale
Graphite crystal structure
Part-2: BASED ON ENGINEERING FUNDA
If v=220V, I=25A, power factor=0.8, frequency=400Hz. If the motor runs for 3 hours, what is the power consumed?
Symbol of capacitor?
Boiling point of mercury?
When salt is added to water, what happens to its freezing point?
What motor do they use in railway engines for traction?
DC Shunt motor b. DC Series motor
What motor is used for running lathe spindle?
Type of magnetic material used for small motors.
Diamagnetic b. paramagnetic c. ferromagnetic
What types of images do concave and convex lenses produce?
What is the speed of 3-phase induction motor?
Which gear type does not have axial thrust? Ans: Herringbone
Determinant value? Ans: 0
Which of the following is not a thermal radiation law? Ans: Lamberts law
In which units sound is measured? Ans:Decibels
Velocity of sound at sea level?
Which of the following is formed due to the attraction between moon and earth? Ans:Tides
Instrument used for measurement of high temperatures? Ans:Pyrometer
Thread used in lathe leadscrew? Ans:ACME Thread
If water is air, air is dust, dust is light, light is sound, and sound is water, where does fish live?
If the barometer shows 300mm Hg, what is the absolute pressure?
What is the 4-1 process in otto cycle?
Power stroke in diesel cycle is what process? Ans:Adiabatic process
Which of the following does not form a real image?
Concave b. Convex c. telescope d. microscope
At what temperature °C and K are the same?
What is the material used in permanent magnet?
An object weighs 3kg in air, 2.5kg in water, what is its density?
Which material has the highest Cp value?
air b. water c. copper
Which of the following has lowest thermal conductivity?
steel b. SS c. Bronze d. copper
The crystalline structure of graphite is
a. Simple cubic b. FCC c. BCC d. HCP
Which process cannot be used to produce external threads?
forging b. Rolling c. milling d. turning
The axial stress on a member which is subjected to a sudden load when compared to load applied gradually is
a. same b. double c. half d. quadraple
Silencer reduces noise. It also
gives balance to engine b. increases fuel consumption c. Decreases fuel consumption d. reduces vibrations
Unit of kinematic viscosity.
Unit of surface tension.
Meaning of overdrive
Wankel engine
Meaning general drill bit angle.
Reason of using regenerator & condenser.
Cycle used in gas cycles, dual cycle& diesel cycle diagram.
Normal value of voltage in spark plug & distributor function.
In which case turning will be easy (front wheel driven back wheel steered/__/___/___).
Viscous fluid passing through duct of varying cross section & pressure remains unchanged-reason?
Differential function
Pitch circle diameter &Pressure angle
Gear hobbler
Gear system in which axial thrust is absent.
Force applied on pin joint of truss (connecting 3 bars, middle straight side slant at equal angle)-tension/compression in middle bar?
Element added to steel for corrosion resistance.(Ans: Cr)
Which has lowest specific heat- water, steam, copper?
Which has lowest thermal conductivity-stainless steel, steel, and bronze?
Diamond pin function.
Relation between stress-gradually applied & suddenly applied.
Increasing of water density in range?(0-4 degree)
1 litre, 4 stroke engine, 1600 rpm, mean thermal effective pressure=5 bar, power of engine?
Finding rpm of single phase alternator from list of rpm’s.
Efficiency of carnot engine.
Temperature measurement based on which law.
Size of lathe(parameters)
Thread can be formed by all process except
Forging b. rolling c. Milling d. Turning
Thread used in screw jack, lead screw?
Which is not related to thermal radiation
planck law b. steffan boltzmann law dc. fourier law
Radiator type used in bus.
Definitions of normalizing, tempering, quenching, etc.
Normal hardness value of cast iron used in lathe bed.(in BHN)
Definitions-straddle milling, slab milling, gang milling etc.
Questions based on getting final 3-D shape, from sheet showing details where it can be folded.
Getting front view, top view, side view of given isometric view.
Material is not removed in which process
punching b. coining c. tapping d. embossing
Part 3: General aptitude (60 Questions: 30 Minutes)
Question Types: Figurative questions (from Edgar Thorpe), Analogy, ratios and proportions, time and work, time and distance, Implicit statement reasoning
1. If the average of the 10 of the 11 player is 30.if the 11th player score is added the average decreases by 2.what is the score of the 11th player.
2. Exonerate –meaning
3. Analogy
Peaceful: resistance then
a) litigation: lawlessness
b) coherent: inconsistency
c) dumb: follow
d) diligent: reliability
e) rough: forceful
Ans :b
4. Cut is to feline, vulpane is to—————.
5. Three problems using codes
a. if AGPSV IS BHQTW, then DKNUY
b. CEGIK then choose the same pattern ans: moqsu
6. Diagram of one block was given. It contains three or four sections. we were asked to find the
a. Left side view. b. Bottom side view c. Back side view.
with regards
saket123