Robert Bosch

Bosch Placement Paper Company: Robert Bosch Bosch PAPER PATTERN by placement papers mncsPAPER PATTERN This pattern below is for computer science (CS) students only. There was another set of paper for MECH branch students. Section 1:This section had only technical question. They were mainly from Pointers in C, C++, Data Structures and some questions on […]

BOSCH Placement Papers Company: Robert Bosch BOSCH There were 75 questions.. total Duration 1 hour 20 mins..1-50 Questions are Technical and in that some 10-15 are Aptitute. it’s very easy.51-75 are Test of English Language..From 1-50 for Correct answer 2 marks for wrong answer -1 mark..From 51-75 for correct answer 1 mark for wrong answer […]

Robert Bosch Placement Paper Company: Robert Bosch Robert Bosch Placement Paper on 17 February 2007 For ELECTRONICS students placement paper 1. There was a figure of JK flip flop in which ~q is connected to J input and K=1. If clock signal is successively applied 6 times what is output sequence (q=?)d) 0101012. Frequency response […]

BOSCH Placement Papers Company: Robert Bosch BOSCH Questions ; 60 (objective)Duration : 1 h This paper is for EEE,ECE,EIE each question carries 1 mark, right answer gives u 1 mark while a wrong answer gives -0.25 marks. 1) given common mode gain =0.02 and differential gain =40 find CMRR in dB….Ans CMRR=20 log(differntial gain/common mode […]

BOSCH Placement Papers Company: Robert Bosch BOSCH Written Test (89/400) Questions; 60Duration: 1 h 1. Basic Electrical-5 q’sHINTS.1. Critical circuit (V, I, R) find the voltage between two points. In one path current source and one R is present. (Easy)2, KVL, KCL3. Theory from reciprocity theorem (not sure but one theorem) 2. Basic electronics-5 q’si. […]

BOSCH Placement Papers Company: Robert Bosch BOSCH 1. Critical stress at which material will start to flow(a)yield(b)ultimate tensile stress(c) proof stress(d) none o the above 2. maximum degree of freedom in spaceAns. 6 3. bearing which will take axial and radial loads.(a) thrust bearing(b) deep groove(c) taper roller(d) roller 4. volume of water per cubic […]

BOSCH Placement Paper Company: Robert Bosch BOSCH BOSCH Placement Papers-1 2004: 1. Critical stress at which material will start to flow(a)yield(b)ultimate tensile stress(c) proof stress(d) none o the above 2. Maximum degree of freedom in spaceAns. 6 3. Bearing which will take axial and radial loads.(a) Thrust bearing(b) deep groove(c) taper roller(d) — 4. Volume […]

Robert Bosch Placement Paper Company: Robert Bosch BOSCH BOSCH Placement Paper-1 Sep 2006 The paper was easy if you have basic knowledge of electronics and C. Most of the questions were of average difficulty. 45 technical Questions and 35 Aptitude questions: Total Time 1:30 Hours2 marks for correct answers and -1 for wrong answers. U […]

Robert Bosch Placement Paper Company: Robert Bosch The interview was for people with 2 years of experience, but I with 1 year of experience, took a chance. I was instructed at the beginning of the interview that “Look, though you do not have 2 years of experience, yet I thought I shall spend some time […]

Robert Bosch Placement Paper Company: Robert Bosch The paper was easy if u have basic knowledge of electronics and C. Most of the questions were of average difficulty. 45 technical Questions and 35 Aptitude questions Total Time 1:30 Hours2 marks for correct answers and -1 for wrong answers. U have to study the following things […]