Company: Robert Bosch ROBERT BOSCH Placement question paper. SECTION 1(TECHNICAL) 1. There was a figure of JK flip flop in which ~q is connected to J input and K=1. If clock signal is successively applied 6 times what is output sequence (q=?) d) 010101 2. Frequency response of a filter is a) Range of frequencies […]
Robert Bosch Placement Papers
Posted inPlacement Papers
Ericssion Whole Testpaper
Company: Robert Bosch Test paper had 3 sections.Total 75 questions. followed by Technical interview..& HR interview.. 1.Basics of Telecommunications-45 questions 2.Computer network/UNIX/tcp-ip-10 question 3.Aptitude-20 Question Some of the question are- Section-I 1.The attenuation in wave guides near the cutoff frequency is- a)Zero b)Very Low c)Medium High 2.The VHF band is- a)30 hz-300hz b)300Hz-3Khz c)3Khz-30Khz d)30 […]
Posted inPlacement Papers
Robert Bosch Placement Paper
Company: Robert Bosch Robert Bosch 1. Critical stress at which material will start to flow (a)yield (b)ultimate tensile stress (c) proof stress (d) none o the above 2. maximum degree of freedom in space Ans. 6 3. bearing which will take axial and radial loads. (a) thrust bearing (b) deep groove (c) taper roller (d) […]
Posted inPlacement Papers
Bosch Placement Paper
Bosch Placement Paper Company: Robert Bosch Bosch PAPER PATTERN by placement papers mncsPAPER PATTERN This pattern below is for computer science (CS) students only. There was another set of paper for MECH branch students. Section 1:This section had only technical question. They were mainly from Pointers in C, C++, Data Structures and some questions on […]
Posted inPlacement Papers
BOSCH Placement Papers on 05 Dec 2004
BOSCH Placement Papers Company: Robert Bosch BOSCH There were 75 questions.. total Duration 1 hour 20 mins..1-50 Questions are Technical and in that some 10-15 are Aptitute. it’s very easy.51-75 are Test of English Language..From 1-50 for Correct answer 2 marks for wrong answer -1 mark..From 51-75 for correct answer 1 mark for wrong answer […]
Posted inPlacement Papers
Robert Bosch Placement Paper on 17 February 2007
Robert Bosch Placement Paper Company: Robert Bosch Robert Bosch Placement Paper on 17 February 2007 For ELECTRONICS students placement paper 1. There was a figure of JK flip flop in which ~q is connected to J input and K=1. If clock signal is successively applied 6 times what is output sequence (q=?)d) 0101012. Frequency response […]
Posted inPlacement Papers
BOSCH Placement Papers
BOSCH Placement Papers Company: Robert Bosch BOSCH Questions ; 60 (objective)Duration : 1 h This paper is for EEE,ECE,EIE each question carries 1 mark, right answer gives u 1 mark while a wrong answer gives -0.25 marks. 1) given common mode gain =0.02 and differential gain =40 find CMRR in dB….Ans CMRR=20 log(differntial gain/common mode […]
Posted inPlacement Papers
BOSCH Placement Papers
BOSCH Placement Papers Company: Robert Bosch BOSCH Written Test (89/400) Questions; 60Duration: 1 h 1. Basic Electrical-5 q’sHINTS.1. Critical circuit (V, I, R) find the voltage between two points. In one path current source and one R is present. (Easy)2, KVL, KCL3. Theory from reciprocity theorem (not sure but one theorem) 2. Basic electronics-5 q’si. […]
Posted inPlacement Papers
BOSCH Placement Papers
BOSCH Placement Papers Company: Robert Bosch BOSCH 1. Critical stress at which material will start to flow(a)yield(b)ultimate tensile stress(c) proof stress(d) none o the above 2. maximum degree of freedom in spaceAns. 6 3. bearing which will take axial and radial loads.(a) thrust bearing(b) deep groove(c) taper roller(d) roller 4. volume of water per cubic […]
Posted inPlacement Papers
BOSCH Placement Paper
BOSCH Placement Paper Company: Robert Bosch BOSCH BOSCH Placement Papers-1 2004: 1. Critical stress at which material will start to flow(a)yield(b)ultimate tensile stress(c) proof stress(d) none o the above 2. Maximum degree of freedom in spaceAns. 6 3. Bearing which will take axial and radial loads.(a) Thrust bearing(b) deep groove(c) taper roller(d) — 4. Volume […]