Bosch Placement Paper

Company: Robert Bosch

Bosch PAPER PATTERN by placement papers mncs
PAPER PATTERN

This pattern below is for computer science (CS) students only. There was another set of paper for MECH branch students.

Section 1:This section had only technical question. They were mainly from Pointers in C, C++, Data Structures and some questions on OS, DBMS.This section also had lots of question on bit conversions (HEX to Binary, decimal) and one question on finding 2’s compliment and such others. There were few questions on finding TRUE/FALSE statement which was bit confusing. Question to calculate square root, cube root of a number were also included.
Overall, this section was easy if you are good with your basics. The questions were mainly around the basic concepts only.
Each question had four options (A, B, C, D) and we had to find the most appropriate answer. Each correct answer carries 2 marks and there is a negative marking of 1 for each wrong answer. So be careful while attempting these questions.

Section 2:This had only general English questions. No book will help you to answer these questions; instead you should have good knowledge of grammar and different English works.
There was a paragraph with some blanks in between. So we had to find the appropriate words to fill in, from the given options. Other questions included comprehension, synonyms, proverbs type question and others.
This section needs some intelligent guessing as you feel that all of the given options are correct and sometimes all are wrong.
Each correct answer carries 1 mark and there is a negative mark of 0.5.

BOSCH REXROTH AG , Vatva , Ahmedabad, ON 24th Aug. 2004

1. Critical stress at which material will start to flow
(a)yield
(b)ultimate tensile stress
(c) proof stress
(d) none o the above

2. maximum degree of freedom in space Ans. 6

(a) thrust bearing
(b) deep groove
(c) taper roller
(d) —

4. volume of water per cubic metre of air.
(a)specific volume
(b) specific gravity
(c) vapour pressure
(d) none of above

5. fluid is flowing through a frustum of cone. what is the nature of graph of velocity Vs. c/s area. {flow = velocity X c/s area}
(a) parabola
(b) hyperbola
(c) y=mx+c
(d) x=x.

6. Fluid in a pipe having no change in profile with change in length of pipe …explain type of flow.
a)Laminar
b)Turbulent
c)fully developed profile

7. Which are correct
I) Navier Stokes Eq. is …. of momentum conservation eq.
II)bernoulis eq. is for viscous flow
III) REYNOLD no. >3000 always for turbulent flow.
a)I and II correct
b)I and II not correct
c)II and III correct
d)II and III not correct

8. Which can’t be removed during alloying from Fe alloys
a) co
b) N
c) Si
d) As

9.There are two ropes burning non uniformly (rate) and clock half an hour each. which can’t be clocked ?
a) 1 Hr.
b) 45 min
c)15 min
d)none

10. Lim n->0 (1+ 1/n)^n =
a) 1
b)0
c)e
d)infinity

11.time dependent increase in length at steady temp. is called
a) superplasticity
b) creep
c) fatigue
d) none

12. Vicosity change with increasing temp.
a) decreases
b) increases
c) same
d) first decreases and then increases.

13. Direction of friction in bicycle tyres
a) along motion
b) opp. motion
c) Front opp. motion and vice versa
d) rear opp. motion and vice versa

14. Sp. gravity of a fluid
a) density of fluid at 0`c / density of water at o`c.
b) density of fluid at 0`c / density of water at T`c.
c) density of fluid at T`c / density of water at o`c.
d) density of fluid at T`c / density of water at T`c.

15. lateral strain / longitudinal strain
a) Poission’s Ratio
b) Bulk Modulus
c) Modulus Of Elasticity
d) None

16. 10 coins & 1 defected coin and 2 weighs Find min weighs req. to detect faulty coin
a) 2
b)3
c)4
d)5

17. 9 members in meeting scheluled at 10:00 A.M. , all reaches at 9:48 A.M. . one member req. 2 min to intro with other find meeting delay with scheduled time of 10:00 A.M..
a) 1 Hr.
b) 6 min
c) …
d)At scheduled time

18. A completes job in 10 hr. and B completes in 15 hr.. Find when both together works
a) 6 hr.
b) 8 hr
c) 10 hr
d) none

19. A ball dropped from H height and moves 80% of height each time.Total dist. covered
a) 4H
b) 5H
c) 7H
d) 9H

20. A cantilever beam loaded at free end find reinforcement place
a) AT neutral axis
b) above neutral axis
c) below neutral axis
d) above and below neutral axis

21. punching a sheet of D dia and T thickness and S ultimate tensile stress
a) 3.14 DTS
b) 3.14TS X D^2
c) 6.28 DTS
d)6.28 TS x D^2

22. …

23. two easy ques. of string mass equilibrium system…

24. Microstructure after quenching
a) Mertensite
b) pearlite
c) ……..
d)……….